แสดงบทความที่มีป้ายกำกับ Insulation แสดงบทความทั้งหมด
แสดงบทความที่มีป้ายกำกับ Insulation แสดงบทความทั้งหมด

วันอาทิตย์ที่ 18 ธันวาคม พ.ศ. 2554

How To Install Blown In Attic Insulation

Scenario:

I have just completed an addition to my house. I've heard that blown in insulation is better than batts since covers the joists completely and leaves no open areas. Do you have any do it yourself suggestions?

Solution:

Yes you are correct. Blown in insulation is better that batts when installed properly as it does seal the attic better.

First you need to measure your attic area that you plan on insulating. Most attics require a value of R-30, R-38 or R-49, depending on your climate and location. Once you know the square footage of your attic you can determine how much insulation you'll need by simple looking on the chart located on the bag of insulation.

Before you get started you will need to determine what materials you will need. Assuming your home has recessed lights, ceiling and bathroom fans and eave vents you will need the following tools and materials:

Loose Fill Insulation

Cardboard Baffles

Flashing

Duct Tape

Staple Hammer and Staples

Utility Knife

Ladder

Insulation Blowing Machine (Available at your local rental store)

The attic will need preparation before you can actually blow insulation into it. Make sure you are wearing a dust mask, protective goggles and a long sleeve shirt. Recessed lights must have flashing installed around them leaving a open space of at least four inches from the flashing to the light. Using a utility knife cut a piece of flashing of the correct length and form it into a cylinder shape, securing the edge with duct tape. Place over recessed light leaving a four inch open area. This allows for the heat to escape. Use the same process for any vented kitchen or bathroom fans in the attic area.

The next step is baffles. This is a chore nobody enjoys. The baffles need be installed by using your staple hammer and install them where the ceiling joists intersect with roof rafters. Make sure you only install the baffles over the vents and that they are high enough so the vents won't get covered with insulation. Now that you've installed you might want to climb out of the attic and give you back a much needed rest.

The next step of preparation is to make a dam around the attic access hole. The easiest way is to cut a few extra cardboard baffles into lengths of about 4 inches above the amount of insulation you plan on installing. Simply staple them around the perimeters of the access hole. This will allow for a uniform depth in the insulation you are blowing in.

So you don't have to keep crawling in and out of the attic it's best to have another person outside helping you load the insulation blowing machine. Hint: If you're using fiberglass insulation have your helper add about a cup of water per bag, spreading it over the top after its loaded into the machine. This will help cut down static electricity when you are blowing the insulation and it will lay down more evenly when installing it. After the bag of insulation is loaded into the hopper it will take several minutes before the next bag is needed. Don't let your helper be lazy. Have him get on the ladder and pull excess hose out of the attic for you so you don't get tangled in it.

I've found blowing insulation into the attic is a simple process. Start and the far ends of the attic. Going back and forth make sure its level and smooth. Make sure to get all areas of the attic and don't fill any vents or recessed light areas. Take a tape measure with you and check the levels once in a while. As an example, if your installing an R-38 of fiberglass insulation you would want it to measure 16 inches deep. As you work your way back near the attic access make sure your helper is getting that excess hose out of the way. When you get to about 6 feet from the access hole stop the machine so you can get on the ladder. Once on the ladder finish installing, making sure to bring the level evenly against the dam you previously built.

The final step is to place a piece of batt insulation in the access hole and carefully put the attic hole lid back into place. Now your done! Stay out of that attic as much as possible from this point as loose fill insulation that has been stepped on or crushed looses it's R value.

Related : Buy Best Price Buy Best Price Jewelry Cheap Price McAfee Total Protection Discount Electronics Gifts

วันศุกร์ที่ 29 ตุลาคม พ.ศ. 2553

Going Green with Construction - Insulation

There is a new trend in construction - building with environmental concerns in mind. In this article, we cover going green with insulation in a structure.

Insulation is one of the more urgent green issues in construction. Proper insulation can have such an important role in the reduction of energy waste in a home. The well insulated home holds in the heat and keeps out the cold. Today, with the wide spread use of air conditioning, the opposite is just as true and just as critical. Asbestos and vermiculite, compound containing asbestos, have been widely used as insulating materials. It was efficient and easy to install. It was flame retardant. There were many reasons that made it the popular choice. It was, however, highly toxic.

The story of asbestos insulation is a good example of the totality of the green construction movement. The concept is not about trade offs. We do not pollute our water in order to have more material goods from our factories. We do not foul our air to have less expensive automobiles. We also do not risk our health to have an inexpensive insulation, regardless of how efficient it might be or how well it prevents fires.

There are alternatives, and when we approach these alternatives from the perspective of totality, we often find they are better and less expensive anyway. In the case of insulation, one good example is insulation made from recycled cotton. The cotton insulation is 100 percent recyclable and it is non-toxic. The manufacturing process uses less energy than the manufacturing of asbestos products or even fiber glass insulation.

Another alternative insulation is vegetable oil based polyurethane. It is sprayed into the areas needing insulation and when it contacts air it expands filling in the space completely. This allows an extra tight fit that results in even better insulation than the more toxic insulations that it is designed to replace. These alternative insulations are free of VOC and CFC. These are volatile organic compounds (VOC) and chlorofluorocarbons (CFC) which are common toxic substances in older types of insulation.

Insulation is a major component of going green in construction. The conservation of heat and the reduction of wasted energy are important standards. Yet, green construction is not about trading off one hazard for another, nor reaching one goal by failing to consider its impact on other environmental areas. So, even though insulation is an important part of building green, selecting environmentally safe insulation is just as important. The good news is that, as is often the case, the right choice is not only the safer choice, but many times the least expensive option as well.

More review : Apparel on Sale Buy On Sale audiobook download Netbook Black Friday Cheap